|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
CM1421 4-Channel LCD EMI Filter Array plus 4-Channel ESD Protection Array Features * * * * * * * Functionally and pin compatible with CMD's CSPEMI607 Four channels of combined EMI/RFI filtering plus ESD protection Four additional channels of ESD-only protection Better than 30dB attenuation (typical) at 1 GHz 15kV ESD protection on all channels (IEC 61000-4-2 Level 4, contact discharge) 30kV ESD protection on all channels (HBM) Chip Scale Package features extremely low lead inductance for optimum filter and ESD performance 15-bump, 2.960mm X 1.330mm footprint Chip Scale Package (CSP) OptiguardTM coated for improved reliability Lead-free version available Product Description The CM1421 is a multichannel array consisting of four low-pass filters with integrated ESD protection and four ESD-only protection channels designed to reduce EMI/ RFI emissions on LCD data lines in mobile handsets. The CM1421 has component values of 15pF-10015pF. These devices include ESD protection diodes on every pin, which provide a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The ESD diodes connected to the filter ports are designed and characterized to safely dissipate ESD strikes of 15kV, beyond the maximum requirement of the IEC 61000-42 international standard. Using the MIL-STD-883 (Method 3015) specification for Human Body Model (HBM) ESD, the pins are protected for contact discharges at greater than 30kV. This device is particularly well suited for portable electronics (e.g. wireless handsets, PDAs, notebook computers) because of its small package format and easyto-use pin assignments. In particular, the CM1421 is ideal for EMI filtering and protecting data lines from ESD for the LCD display in clamshell handsets. The CM1421 incorporates OptiguardTM coating which results in improved reliability. The CM1421 is available in space-saving, low-profile chip-scale packages with optional lead-free finishing. * * * Applications * * * * * LCD data lines in mobile handsets EMI filtering and ESD protection for both data and I/O ports Mobile Handsets Handheld PCs / PDAs Notebook Computers Electrical Schematic 100 FILTER+ESDn* 15pF 15pF FILTER+ESDn* ESDn* 15pF GND (Pins B1-B3) 1 of 4 EMI/RFI + ESD Channels. 1 of 4 ESD-only Channels * See Package/Pinout Diagram for expanded pin information (c) 2004 California Micro Devices Corp. All rights reserved. 04/27/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 1 CM1421 PACKAGE / PINOUT DIAGRAMS TOP VIEW (Bumps Down View) Orientation Marking (see note 2) BOTTOM VIEW (Bumps Up View) 1 A B C 2 3 4 5 6 ESD_3 FILTER+ESD_2 FILTER+ESD_4 C1 C2 FILTER+ESD_1 C3 GND C4 FILTER+ESD_3 C5 GND C6 ESD_4 N213 Orientation Marking GND ESD_1 B1 A2 FILTER+ESD_1 B2 A4 FILTER+ESD_3 B3 A6 ESD_2 FILTER+ESD_2 FILTER+ESD_4 A1 A1 A3 A5 Notes: CSP Package 1) These drawings are not to scale. 2) Lead-free devices are specified by using a "+" character for the top side orientation mark. CM1421-03 PIN DESCRIPTIONS PIN(s) A1 A2 A3 A4 A5 A6 B1-B3 C1 C2 C3 C4 C5 C6 NAME ESD_1 FILTER+ESD_1 FILTER+ESD_2 FILTER+ESD_3 FILTER+ESD_4 ESD_2 GND ESD_3 FILTER+ESD_1 FILTER+ESD_2 FILTER+ESD_3 FILTER+ESD_4 ESD_4 DESCRIPTION ESD Channel 1 Filter + ESD Channel 1 Filter + ESD Channel 2 Filter + ESD Channel 3 Filter + ESD Channel 4 ESD Channel 2 Device Ground ESD Channel 3 Filter + ESD Channel 1 Filter + ESD Channel 2 Filter + ESD Channel 3 Filter + ESD Channel 4 ESD Channel 4 Ordering Information PART NUMBERING INFORMATION Standard Finish Ordering Part Pins 15 Package CSP Number1 CM1421-03CS Part Marking N213 Lead-free Finish Ordering Part Number1 CM1421-03CP Part Marking2 N213 Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Note 2: Lead-free devices are specified by using a "+" character for the top side orientation mark. (c) 2004 California Micro Devices Corp. All rights reserved. 2 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 04/27/04 CM1421 Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER Storage Temperature Range DC Power per Resistor DC Package Power Rating RATING -65 to +150 100 500 UNITS C mW mW STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range RATING -40 to +85 UNITS C ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE1) SYMBOL R C VDIODE ILEAK VSIG PARAMETER Resistance Capacitance Diode Standoff Voltage Diode Leakage Current (reverse bias) Signal Voltage Positive Clamp Negative Clamp In-system ESD Withstand Voltage a) Human Body Model, MIL-STD-883, Method 3015 b) Contact Discharge per IEC 61000-4-2 Level 4 Clamping Voltage during ESD Discharge MIL-STD-883 (Method 3015), 8kV Positive Transients Negative Transients Cut-off Frequency ZSOURCE=50, ZLOAD=50 At 2.5V DC IDIODE=10A VDIODE=3.3V ILOAD = 10mA 5.6 -1.5 Notes 2,4 and 5 6.8 -0.8 9.0 -0.4 V V kV kV CONDITIONS MIN 80 12 5.5 100 TYP 100 15 MAX 120 18 UNITS pF V nA VESD 30 15 Notes 2,3,4 and 5 +12 -7 R=100 , C=15pF 120 VCL V V MHz fC Note 1: TA=25C unless otherwise specified. Note 2: ESD applied to input and output pins with respect to GND, one at a time. Note 3: Clamping voltage is measured at the opposite side of the EMI filter to the ESD pin. For example, if ESD is applied to Pin A2, then clamping voltage is measured at Pin C2. Note 4: Unused pins are left open Note 5: These parameters are guaranteed by design and characterization. (c) 2004 California Micro Devices Corp. All rights reserved. 04/27/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 3 CM1421 Performance Information Typical Filter Performance (TA=25C, DC Bias=0V, 50 Ohm Environment) Figure 1. Insertion Loss VS. Frequency (A1-C1 to GND B1) Figure 2. Insertion Loss VS. Frequency (A2-C2 to GND B1) (c) 2004 California Micro Devices Corp. All rights reserved. 4 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 04/27/04 CM1421 Performance Information (cont'd) Typical Filter Performance (TA=25C, DC Bias=0V, 50 Ohm Environment) Figure 3. Insertion Loss VS. Frequency (A3-C3 to GND B2) Figure 4. Insertion Loss VS. Frequency (A4-C4 to GND B2) (c) 2004 California Micro Devices Corp. All rights reserved. 04/27/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 5 CM1421 Performance Information (cont'd) Figure 5. Filter Capacitance vs. Input Voltage over Temperature (normalized to capacitance at 2.5VDC and 25C) (c) 2004 California Micro Devices Corp. All rights reserved. 6 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 04/27/04 CM1421 Application Information Refer to Application Note AP-217, "The Chip Scale Package", for a detailed description of Chip Scale Packages offered by California Micro Devices. PRINTED CIRCUIT BOARD RECOMMENDATIONS PARAMETER Pad Size on PCB Pad Shape Pad Definition Solder Mask Opening Solder Stencil Thickness Solder Stencil Aperture Opening (laser cut, 5% tapered walls) Solder Flux Ratio Solder Paste Type Pad Protective Finish Tolerance -- Edge To Corner Ball Solder Ball Side Coplanarity Maximum Dwell Time Above Liquidous Soldering Maximum Temperature VALUE 0.275mm Round Non-Solder Mask defined pads 0.325mm Round 0.125mm - 0.150mm 0.330mm Round 50/50 by volume No Clean OSP (Entek Cu Plus 106A) 50m 20m 60 seconds 260C Non-Solder Mask Defined Pad 0.275mm DIA. Solder Stencil Opening 0.330mm DIA. Solder Mask Opening 0.325mm DIA. Figure 6. Recommended Non-Solder Mask Defined Pad Illustration 250 Temperature (C) 200 150 100 50 0 1:00.0 2:00.0 3:00.0 Time (minutes) 4:00.0 Figure 7. Eutectic (SnPb) Solder Ball Reflow Profile (c) 2004 California Micro Devices Corp. All rights reserved. 04/27/04 Figure 8. Lead-free (SnAgCu) Solder Ball Reflow Profile 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 7 CM1421 Mechanical Details CSP Mechanical Specifications CM1421 devices are packaged in a custom Chip Scale Package (CSP). Dimensions are presented below. For complete information on CSP packaging, see the California Micro Devices CSP Package Information document. C1 Mechanical Package Diagrams BOTTOM VIEW A1 B1 C B2 B4 B3 OptiGuardTM Coating PACKAGE DIMENSIONS Package Bumps Dim A1 A2 B1 B2 B3 B4 C1 C2 D1 D2 Millimeters Min 2.915 1.285 0.495 0.245 0.430 0.430 0.180 0.180 0.600 0.394 Nom 2.960 1.330 0.500 0.250 0.435 0.435 0.230 0.230 0.670 0.445 Max 3.005 1.375 0.505 0.255 0.440 0.440 0.280 0.280 0.739 0.495 Min Custom CSP 15 Inches Nom Max 0.1148 0.1165 0.1183 0.0506 0.0524 0.0541 0.0195 0.0197 0.0199 0.0096 0.0098 0.0100 0.0169 0.0171 0.0173 0.0169 0.0171 0.0173 0.0071 0.0091 0.0110 0.0071 0.0091 0.0110 0.0236 0.0264 0.0291 0.0155 0.0175 0.0195 3500 pieces A2 C2 B A 1 2 3 4 5 6 0.30 DIA. 63/37 Sn/Pb (Eutectic) or 95.5/3.8/0.7 Sn/Ag/Cu (Lead-free) SOLDER BUMPS D1 D2 SIDE VIEW DIMENSIONS IN MILLIMETERS Package Dimensions for CM1421 Chip Scale Package # per tape and reel Controlling dimension: millimeters CSP Tape and Reel Specifications PART NUMBER CM1421 CHIP SIZE (mm) 2.96 X 1.33 X 0.6 POCKET SIZE (mm) B0 X A0 X K0 3.10 X 1.45 X 0.74 Po Top Cover Tape TAPE WIDTH W 8mm REEL DIAMETER 178mm (7") QTY PER REEL 3500 P0 4mm P1 4mm 10 Pitches Cumulative Tolerance On Tape 0.2 mm Ao W Ko Bo For Tape Feeder Reference Only including Draft. Concentric Around B. Embossment P1 User Direction of Feed Center Lines of Cavity Figure 9. Tape and Reel Mechanical Data (c) 2004 California Micro Devices Corp. All rights reserved. 8 430 N. McCarthy Blvd., Milpitas, CA 95035-5112 Tel: 408.263.3214 Fax: 408.263.7846 www.calmicro.com 04/27/04 |
Price & Availability of CM1421-03CS |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |